In the attached file you can find the following topics related to the F120 3D printer


1.- SERVICE AND SUPPORT

  • Hazard Types
  • Product Safety Signs
  • Product Safety Label Locations
  • Potential Safety Hazard Areas
  • Door Locks 
  • General Safety Practices
  • Environmental Requirements

2.- PRINTER SETUP

  • Welcome Kit Contents
  • Identifying Your Printer
  • Making the Network Connection
  • Connecting the Power Cable
  • Configuring the Network
  • Installing GrabCAD Print
  • Connecting to the F120 Printer
  • Setting the Printer’s Date and Time
  • Updating the Controller software Version
  • Adjusting the Tip Wipe Height

3.- SYSTEM COMPONENTS

  • Access Doors and Panels
  • Interface Panel
  • Oven Door
  • Oven Light
  • Platen
  • Tip Wipe Assemblies
  • Purge Chute
  • Material Coil Box
  • Print Heads
  • Materials Used
  • Material Coil Box Memory Chip
  • Tips and Slice Height
  • Controller Software
  • GrabCAD Print Software

4.- USER INTERFACE

  • Navigation Menu
  • Display Area
  • Loading a File
  • Viewing Print Job Information
  • Build Status Display
  • Print Job Controls
  • Adding a Job to the Job Queue
  • Editing the Job Queue
  • Viewing Job Details
  • About the Sample Queue
  • Head Status Icons
  • Viewing Head Details
  • Material Status Icons
  • Viewing Material Details
  • Material Load Controls
  • Tools Page Menu
  • Navigation Overview
  • Settings
  • Calibration
  • Maintenance
  • Network
  • Power
  • Light 

5.- OPERATING THE PRINTER

  • Powering ON the Printer
  • Powering OFF the Printer
  • Material Coil Box Preparation
  • Connecting Material Coil Box To Printer
  • Handling/Storing Materials
  • Replacing a Head
  • Before a Build
  • Preparing the Printer
  • Selecting a Job to Build
  • Information Available During a Build
  • Build Warnings
  • Pausing a Build
  • Aborting a Build
  • After a Build is Complete
  • Job Storage
  • Part Build Location
  • Display Units
  • Oven Temperature Control
  • Touchscreen Display Brightness
  • Display Language
  • Head Odometer Status
  • Materials Status
  • Temperature Status
  • Software Version
  • MTConnect System Activation

6.- CALIBRATION AND ADJUSTMENTS

  • Automatic Tip Calibration
  • Manual Tip Calibration

7.- MAINTENANCE

  • USB Flash Drive Method
  • GrabCAD Print Method
  • USB Flash Drive Method
  • GrabCAD Print Method
  • Cleaning the Oven Chamber
  • Cleaning the Platen
  • Clean/Inspect Tip Wipe Assemblies
  • Cleaning the Exterior Surface of the Printer
  • Cleaning the Touchscreen Display
  • Inspecting and cleaning the tip shields
  • Cleaning the Oven Door glass Surfaces
  • Powering Off
  • Rear Panel
  • Right and Left Side Panels
  • Right and Left Side Louver Panels
  • Top Cover Assembly
  • 3.3/5/12 VDC ATX Power Supply
  • Oven Thermistor
  • Replacing a Head
  • Head Ribbon Cables
  • Touchscreen Display
  • Right and Left Side Oven Blowers
  • Oven Door Gasket
  • Z Drive Belt
  • Y Bellows
  • Oven Light
  • Oven Door CameraOven Door Latch
  • Top Cover Interlock Sensor and Actuator

8.- TROUBLESHOOTING

  • Warnings at Build Start
  • Errors Preventing a Build from Starting
  • Load/Unload Errors
  • Build Pause Warnings
  • Build Abort Errors
  • Head Warnings
  • Head Errors

9.- SUPPLEMENTARY INFO

  • EMC Class A Warning
  • FCC Statements (U.S.A.)
  • Canada Electromagnetic compatibility (EMC)
  • MSDS (Material Safety Data Sheet)
  • Disposal of Waste Equipment by Users in Private Households in the European Union